6. Ad-hoc networks, MANETs PA191: Advanced Computer Networking. Eva Hladká Slides by: Tomáš Rebok Faculty of Informatics Masaryk University Autumn 2021 Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 1/69 Lecture Overview Q Wireless Ad-hoc Networks • Motivation o (Mobile) Wireless Ad-hoc Networks • Wireless Sensor Networks o MANETs vs. WSNs • MANETs vs. P2P Q Medium Access Control in Ad-hoc and Sensor Networks • Protocols' Classification o Contention-based protocols • Improving Energy Efficiency Q Ad-hoc Routing • Address-based Ad-hoc Routing Protocols • Proactive Protocols o Reactive Protocols • Specialized Routing Protocols Q Conclusion & Information Sources Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 2/69 Lecture Overview Q Wireless Ad-hoc Networks • Motivation o (Mobile) Wireless Ad-hoc Networks • Wireless Sensor Networks o MANETs vs. WSNs • MANETs vs. P2P Q Medium Access Control in Ad-hoc and Sensor Networks • Protocols' Classification • Contention-based protocols • Improving Energy Efficiency Q Ad-hoc Routing • Address-based Ad-hoc Routing Protocols • Proactive Protocols • Reactive Protocols • Specialized Routing Protocols Q Conclusion & Information Sources Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 3/69 Wireless Ad-hoc Networks Motivation Wireless Networks I. • A need: how to access computing and communication services on the move? • =>> wireless networks • wireless networks are traditionally based on a cellular infrastructure 9 a land area that should be covered with a radio service is divided into cells • each cell is covered by a (base) station • base stations connected to a wired backbone network • the mobile nodes communicate wirelessly to these stations • traffic between different mobile entities is relayed by base stations and wired backbone • mobility is supported by switching from one base station to another • e.g., GSM, UMTS, WLAN, ... 4/69 Wireless Ad-hoc Networks Motivation ireless Networks I. • but what, if: • no infrastructure becomes available? (e.g., disaster areas, emergency operations) • e.g., hurricane Cathrina (2005) destroyed huge parts of New Orleans including communication networks • it is too expensive to set it up? (e.g., remote/large places, construction areas) • there is no time to set it up? (e.g., military operations) • =4> Wireless Ad-hoc Networks • try to construct a network without infrastructure, using networking abilities of the participants • ad-hoc network = a network constructed on demand "for a special purpose" o the term ad-hoc is Latin meaning "for this purpose" Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 5/69 Wireless Ad-hoc Networks (Mobile) Wireless Ad-hoc Networks Wireless Ad-hoc Networks Wireless Ad-hoc Network o a collection of autonomous nodes that communicate with each other by forming a multihop radio network and maintaining connectivity in a decentralized manner • each node functions as both a host and a router • the control of the network is distributed among the nodes • the network topology is (in general) dynamic • the connectivity among the nodes may vary in time due to node departures, new node arrivals, and the nodes' mobility • ^> a need for efficient routing protocols that allow the nodes to communicate over multihop paths in an efficient way • these networks pose many complex issues =4> there are many open problems for research • without a central infrastructure, things become much more difficult Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 6/69 Wireless Ad-hoc Networks (Mobile) Wireless Ad-hoc Networks Wireless Ad-hoc Networks Simple example _ ^^^^ [{[r^Hj Figure: Simple example: laptops in a conference room - a single-hop ad-hoc network (all the networking nodes are in a direct communication range of each other node). Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 7/69 Wireless Ad-hoc Networks (Mobile) Wireless Ad-hoc Networks Wireless Ad-hoc Networks Multihop Network example Figure: Multihop (mobile) ad-hoc network example. Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 8/69 Wireless Ad-hoc Networks (Mobile) Wireless Ad-hoc Networks Wireless Ad-hoc Networks Advantages • very fast construction • no need to establish wired connections • resilient • no single point of failure, such as a base station • spectrally more efficient than cellular networks • every node can communicate with any other node (sometimes even simultaneously), so nodes can make better use of the channel Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 9/69 Wireless Ad-hoc Networks (Mobile) Wireless Ad-hoc Networks Wireless Ad-hoc Networks Problems/Challenges • problems arise due to: • lack of a central entity for network organization • the participating nodes must organize themselves into a network • self-organization is a must • limited range of wireless communication • data have to be delivered over a path involving multiple nodes • =>> mechanisms for dynamic path identification and management are required • mobility of participants • the network nodes may be allowed to move in time and space • the network quality depends on the speed to adapt to new topologies • Mobile Ad-hoc Networks (MANETs) • among others, the following issues have to be addressed: • medium access control - no base station can assign transmission resources (it must be decided in a distributed fashion) • routing - finding a route from one participant to another Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 10/69 Wireless Ad-hoc Networks (Mobile) Wireless Ad-hoc Networks (Mobile) Wireless Ad-hoc Networks Possible Applications Factory floor Disaster recovery Car-to-car automation communication 9 finding out empty parking lots in a city (without asking a server), avoiding traffic jams/congestions, etc. (= VANETs) • search-and-rescue in an avalanche • personal area networking (watch, glasses, PDA, medical appliance, .. .) • military networking: tanks, soldiers, ... • collaborative and distributed computing Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 11 / (Mobile) Wireless Ad-hoc Networks Vehicular Ad-hoc Networks (VANETs) Vehicular Ad-hoc Networks (VANETs) • a technology that uses moving cars as nodes/routers to create a mobile network • the cars are allowed to connect to each other (if being in a wireless range) and thus to create a network with a wide range • in comparison with MANETs, where the nodes move in a random way, the cars tend to move in an organized fashion • moreover, the interactions with roadside equipment can be characterized fairly accurately • more specialized routing protocols may be employed Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 12/69 Wireless Ad-hoc Networks (Mobile) Wireless Ad-hoc Networks (Mobile) Wireless Ad-hoc Networks Comparison with Infrastructure-based networks Infrastructure-based network Ad hoc network Prerequisites Pre-deployed infrastructure, e.g. routers, switches, base stations, servers None Node properties End system only Duality of end system and network functions Connections Wired or wireless Usually wireless Topology Outlined by the pre-deployed infrastructure Self-organized topology maintained by the nodes Network functions Provided by the infrastructure Distributed to all participating nodes Figure: Comparison between infrastructure-based and infrastructure-less (ad-hoc) networks. Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 13/ Wireless Ad-hoc Networks Wireless Sensor Networks Wireless Sensor Networks 9 so far, the participants were devices close to a human user (i.e., interacting with humans) • alternative concept: • instead of focusing interaction on humans, focus on interacting with an environment • network is embedded in an environment (in a random or regular fashion) 9 nodes in such a network are equipped with sensing/actuation to measure/influence the environment • the nodes process information and communicate it wirelessly • Wireless Sensor Networks (WSNs) • or Wireless Sensor &. Actuator Networks (WSANs) Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 14/69 Wireless Ad-hoc Networks Wireless Sensor Networks Wireless Sensor Networks Application Examples Emergency operations • e.g., dropping sensor nodes over a wildfire • each node measures temperature • possible to derive a "temperature map" • e.g., sensor nodes to observe wildlife • Great Duck Island, ZebraNet, etc. Precise agriculture 9 bringing out fertilizer/pesticides/irrigation only where needed Intelligent buildings, bridges • reducing energy wastage by proper humidity, ventilation, air conditioning • needs measurements about room occupancy, Habitat monitoring temperature, air flow • monitoring mechanical stress after earthquakes ■ I Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Wireless Ad-hoc Networks Wireless Sensor Networks Wireless Sensor Networks Sensors - HW 9 sensor HW • processor (and memory) • e.g., Atmel ATmegal28 microcontroller, 16 MHz, 128 kByte flash 9 radio transceiver • e.g., Chipcon CC1000 (315/433/868/915 MHz), CC2400 (2.4 GHz) • battery • possibly in combination with energy harvesting • sensors • light, temperature, motion, .. . 16/69 Wireless Ad-hoc Networks Wireless Sensor Networks Wireless Sensor Networks Sensors - SW • sensor software • event-driven operating principle • e.g., TinyOS Event (Transceiver) System component Event handler System function System function New event (Timer) New event (Data packet) Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 17/69 Wireless Sensor Networks Wireless Sensor Networks Importance of an Energy-efficient Operation • often (but not always), the participants in an ad-hoc network (not only sensor network) draw energy from batteries o it is desirable to sustain a long run time for: • individual nodes/devices • the network as a whole • usually, application demands do not bother with individual nodes, as long as the global application-dependent objective can still be fulfilled • employed networking protocols have to take the limited energy into account and behave in an energy-efficient way • e.g., use routes with low energy consumption (energy/bit) • e.g., take available battery capacity of devices into account • How to resolve conflicts between different optimizations? • some form of recharging or energy scavenging from the environment is often used in order to increase the available energy Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 18 / Wireless Ad-hoc Networks Wireless Sensor Networks Wireless Sensor Networks Required functionality and constraints • Available energy • sensor nodes are operated by batteries that provide limited energy for the node • Processing power • employed micro controllers usually provide very limited processing performance (due to size and energy restrictions) • Memory and storage • the characteristics of the available memory usually correlate with the size of the micro controller • Bandwidth and throughput • wireless radio transceivers are optimized for low-energy operation they provide a relatively small bandwidth to the application • Reliability • depending on the application scenario, the demands for the reliability (both communication reliability and error-proneness of the hardware) can strongly differ 9 Addressing • typically, off-the-shelf sensor nodes do not have a globally unique address pre-programmed networking mechanisms must either dynamically allocate unique addresses or even abandon address-based techniques • Scalability • a primary constraint - the scalability of employed methods and algorithms Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 19/69 Wireless Ad-hoc Networks MANETs vs. WSNs MANETs (VANETs) vs. WSNs Many similarities: • both networks strongly rely on self-organization mechanisms (neighborship relations and network topology maintenance) • both networks have to cope with limited energy in the devices • the energy efficiency of employed algorithms and methods is of the highest importance • both networks often use wireless multi-hop communications Many differences: Resources and properties MANET WSN Available energy Processing power Memory and storage Density and scale Mobility Heterogeneity Varying user demands High Medium High Low High High High Limited1 Low* Low High Low Low Low Depending on the application scenario Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 20/69 Wireless Ad-hoc Networks MANETs vs. P2P MANETs vs. P2P Systems I. Wireless ad-hoc networks have also many similarities with P2P systems: o same paradigm 9 self-organizing network • dynamic topology • responsible for routing queries in a distributed environment • lack managing and centralizing units However, there are also great differences —>> Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 21 / Wireless Ad-hoc Networks MANETs vs. P2P MANETs vs. P2P Systems II. Difference P2P Network MANET Motivation for creating the network Logical infra structure to provide a service A physical infra-structure to provide connectivity Connection Between two nodes Fixed medium and direct Wireless and indirect Connection confidence High (physical connections) Low (wireless connections) Peer location Any Internet point Restricted area Structu re Physical apart from logical structure Physical structure corresponds to logical structure Routing reactive Proactive, reactive Peer behavior Fixed Mobile Broadcast Virtual, multiple unicasts Physical; to all nodes in transmission range area Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 22/69 Wireless Ad-hoc Networks MANETs vs. P2P MANETs vs. P2P Systems III. MANET rather is a platform for P2P applications however, existing solutions for wireline Internet cannot be applied directly on MANET for P2P communication, mainly because: • neighbors at the application layer (P2P view) may not necessarily be neighbors at the network layer (MANET view) ^> in order to deploy P2P applications efficiently in MANETs, existing P2P solutions must be subjected to considerable modifications to take many MANETs specifics into account Application Layer Network Layer Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 23/69 Medium Access Control in Ad-hoc and Sensor Networks Lecture Overview Q Wireless Ad-hoc Networks • Motivation • (Mobile) Wireless Ad-hoc Networks • Wireless Sensor Networks • MANETs vs. WSNs • MANETs vs. P2P Q Medium Access Control in Ad-hoc and Sensor Networks • Protocols' Classification o Contention-based protocols • Improving Energy Efficiency Q Ad-hoc Routing • Address-based Ad-hoc Routing Protocols • Proactive Protocols • Reactive Protocols • Specialized Routing Protocols Q Conclusion & Information Sources Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 24/69 Medium Access Control in Ad-hoc and Sensor Networks I. • Medium Access Control (MAC) • responsible for coordination of nodes' access to a shared transmission media • the goal is to minimize collisions • i.e., simultaneous transmissions, which lead to signal corruptions • medium access in (infrastructure, ad-hoc) wireless networks is difficult mainly because of: • it is impossible (or very difficult) to send and to receive at the same time • from the sender's point of view, it is hard to estimate the interference situation at the receiver's side • high error rates make it rather hard to establish a well coordinated communication link among nodes over the wireless medium • requirements for ad-hoc/sensor networks' MAC protocols: • as usually: high throughput, low overhead, low error rates, .. . • additionally: energy-efficiency Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 25/69 Medium Access Control in Ad-hoc and Sensor Networks I. effects, that contribute to energy wastage: • collisions • wasted effort when two packets (transmissions) collide - the detection of and reaction to collisions, and data retransmissions require additional energy • overhearing • if a node is receiving a packet that is destined for another receiver in the same wireless transmission range, the required energy for receiving the packet (or at least parts of it) and the detection that it is destined to another node are waste efforts • idle listening • since the receiving node has no knowledge when a sender may begin a transmission, it must be idle, waiting for a possible packet reception (energy is wasted for doing nothing) • protocol overhead another issue is a mobility of the nodes: • it can essentially affect the performance (throughput) of the protocol • e.g., bandwidth reservations or exchanged control information may become useless if nodes are moving quickly • =>> protocol design must take this mobility factor into consideration Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 26/69 Classification of MAC Protocols for Wireless Radio Nets MAC protocols for wireless radio networks can be distinguished into the following classes: • Contention-based protocols - description follows • Contention-based protocols with reservation mechanisms o support for real-time traffic using QoS guarantees • use mechanisms for reserving bandwidth a priori • synchronous (require time synchronization among all nodes in the network) and asynchronous (usually rely on relative time information) • e.g., MACA/PR (MACA with Piggy-Backed Reservation) • Contention-based protocols with scheduling mechanisms • focus on packet scheduling at nodes and also scheduling nodes for access to the channel • used to enforce priorities among flows (i.e., QoS support is available) • sometimes battery characteristics (e.g., remaining battery power) are considered while scheduling nodes for access to the channel • e.g., LEACH (Low-Energy Adaptive Clustering Hierarchy), SMACS, TRAMA Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 27/69 Contention-based protocols • no a priori resource reservation • whenever a packet should be transmitted, the node contends with its neighbors for access to the shared channel • if multiple nodes want to access the channel at the very same time, collisions cannot be avoided • ^> contention resolution has to be provided by the protocols • cannot provide QoS guarantees • two approaches: • sender-initiated protocols - the packet transmissions are initiated by the sender node • receiver-initiated protocols - the receiver node initiates the contention-resolution protocol a have to cope with two fundamental problems: • hidden and exposed terminals Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 28/ Medium Access Control in Ad-hoc and Sensor Networks Contention-based protocols Contention-based protocols Hidden and Exposed Terminals Problems • Hidden terminal problem - collision of packets due to simultaneous transmission of those nodes that are not within the direct transmission range of the sender but are within the transmission range of the receiver • Exposed terminal problem - inability of a node, which is blocked due to transmission by a nearby transmitting node, to transmit to another node Medium Access Control in Ad-hoc and Sensor Networks Contention-based protocols Contention-based protocols Main Options to Shut Up Senders To reserve a channel during/for a transmission, two basic options are possible: • receiver informs potential interferers while a reception is on-going • by sending out a signal indicating just that • problem: cannot use the same channel on which actual reception takes place • =4> necessary to use a separate channel for signaling • e.g., Busy tone protocol • receiver informs potential interferers before a reception is on-going • can use same channel • receiver itself needs to be informed, by sender, about impending transmission • potential interferers need to be aware of such information • e.g., MACA protocol Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 30/69 BTMA - Busy Tone Multiple Access • the transmission channel is split into data and control channel 9 general behavior: • when a node wants to transmit a packet, it senses the channel to check whether the busy tone is active • if not, it turns on the busy tone signal and starts transmission 9 problem: very poor bandwidth utilization Si ■ Transmission nm^c of Node N2 L-^ Transmi-SMOA range of Nude Nl Region in which simultaneous transmissions are not passible when node Nl is transmitting data ----^- Bjsy tone Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 31/ MACA — Multiple Access Collision Avoidance well-established MAC protocols in the ad-hoc domain use of additional signaling packets: • sender asks receiver whether it is able to receive a transmission - Request to Send (RTS) • if receiver agrees, it sends out a Clear to Send (CTS) 9 sender sends, receiver acks potential interferers overhear RTS/CTS • RTS/CTS packets carry the expected duration of the data transmission • store this information in a Network Allocation Vector (NAV) Node 1 NAV / _ -► Sender / RTS DATA \ Receiver \ A-m > f AC K Node 4 -► NAV J ti me Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 32/69 Medium Access Control in Ad-hoc and Sensor Networks Improving Energy Efficiency Power-Control MAC (PCM) protocol I. o PCM provides a MAC layer solution for power control by varying the transmission power to reduce the overall energy consumption o the idea: • RTS/CTS handshake messages should be transmitted with the maximum available power pmax 9 the handshake is used to determine the required transmission power pdesired that is used for the subsequent DATA/ACK transfer • the calculation of Pdesired is performed from the signal level of the received RTS in combination with some well known minimum threshold for the received signal strength Rxthresh that is necessary for correctly decoding the messages o the calculation: 9 where pr denotes the received power level and a constant parameter c is used to increase Pdesired according to environmental conditions • can be combined with any RTS/CTS based MAC protocol (i.e., including MACA) Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 33/69 Medium Access Control in Ad-hoc and Sensor Networks Improving Energy Efficiency MACA — Energy Consumption Reduce II. Power-Control MAC (PCM) protocol II. Figure: Transmission ranges used by PCM for RTS/CTS and DATA/ACK, respectively. Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 34/69 Medium Access Control in Ad-hoc and Sensor Networks Improving Energy Efficiency new protocol improving the energy efficiency in multi-hop radio networks primary goal: to retain flexibility of contention-based protocols while improving energy efficiency in multi-hop networks • MACA's idle listening is particularly unsuitable if average data rate is low (most of the time, nothing happens) the idea: switch nodes off and ensure that neighboring nodes turn on simultaneously to allow packet exchange ("rendez-vous") • only in these active periods packet exchanges can happen • requires to exchange a wakeup schedule between neighbors • when awake, essentially perform RTS/CTS • it introduces coarse-grained listen/sleep cycle with a duty-cycle D = y • duty-cycle = a measure for the energy efficiency of a node T A { \ Listen Sleep Listen Sleep ^-^y,-time T Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 35/69 Medium Access Control in Ad-hoc and Sensor Networks Improving Energy Efficiency Sensor-MAC (S-MAC) II. in fact, the listen period is divided to support synchronization between neighboring nodes as well as the contention for the wireless channel using the RTS/CTS handshake mechanism z r _ Sync RTS/CTS Data/Sleep Sync RTS/CTS time • the explicit (time) synchronization was introduced to support low duty-cycle operations of 1 - 10 % • all nodes choose their own listen/sleep schedules • these schedules are shared with their neighbors to make communication between all neighboring nodes possible • each node periodically broadcasts its schedule in a SYNC packet, which provides simple time synchronization • to reduce overhead, S-MAC encourages neighboring nodes to adopt identical schedules • many other variants exist: T-MAC, B-MAC, P-MAC, Z-MAC, etc. Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 36/69 Lecture Overview Q Wireless Ad-hoc Networks • Motivation • (Mobile) Wireless Ad-hoc Networks • Wireless Sensor Networks • MANETs vs. WSNs • MANETs vs. P2P Q Medium Access Control in Ad-hoc and Sensor Networks • Protocols' Classification • Contention-based protocols • Improving Energy Efficiency Q Ad-hoc Routing • Address-based Ad-hoc Routing Protocols • Proactive Protocols o Reactive Protocols • Specialized Routing Protocols Q Conclusion & Information Sources Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 37/69 Ad-hoc Routing • typically, nodes are not within the direct communication range of all other nodes • nodes need to discover routes (consisting of intermediate nodes) through which they can deliver their packets to their distant destinations • = a task of a routing protocol • complicated by the presence of node mobility, and the lack of centralized control • the routing protocol must be coupled with a medium access control (MAC) protocol • the routing protocol specifies to whom a node should transmit the packet • the MAC protocol specifies when it should transmit the packet Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 38/69 Ad-hoc Routing Address-based routing vs. data-centric forwarding I. Ad dress-based routing • the first routing approaches for ad-hoc and sensor networks • messages are directed towards a well-specified particular destination (sink) • =^> these routing protocols require each node to have a network-wide unique address or identifier • provide support for unicast, multicast, and broadcast messages • obvious advantage: the possibility of identifying specific (unique) nodes and sending messages to them Figure: Principles of address-based routing: a data packet carrying the destination address "TO:2" is forwarded along an established path towards its final destination: node 2. Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 39/69 Ad-hoc Routing Ad-hoc Routing Address-based routing vs. Data-centric forwarding II Data-centric forwarding • sometimes (especially in WSNs), the unique addresses are not demanded by the application requirements but only by the employed routing protocols • =>> the addressing scheme can be removed and replaced with the specific semantics of the transmitted messages • node addresses are replaced by a kind of interest of particular nodes • payload information (data) is used to forward messages towards an appropriate destination Waiting for "B" ID:"B" Data Source Waiting for "B" Figure: Principles of data-centric forwarding: messages are forwarded according to their internal meaning - messages of type "B" are transmitted to two sinks, which requested exactly messages of type "B" . 40/69 Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 Ad-hoc Routing Address-based routing vs. Data-centric forwarding III. Address-based routing Data-centric forwarding Routing approach Identification of a path according to the destination address of the data message Determination of the destination of a data message according to the content of the packet Prerequisites Network-wide unique addresses Pre-defined message types and semantics Routing techniques Proactive routing (continuous state maintenance) or reactive routing (on-demand path finding) (probabilistic) flooding schemes or interest-based reverse routing Advantages Usually low delays in connection setup and data dissemination No address information required and simplified self-management and redundancy Disadvantages Network-wide unique address identifiers required Increased overhead for single transmissions Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 Ad-hoc Routing Address-based Ad-hoc Routing Protocols Address-based Ad-hoc Routing Classification of Routing Protocols I. Many different classifications of routing protocols exist: o proactive vs. reactive protocols: • Proactive protocols o discover routes before they are needed 9 provide small latency, but large routing overheads • Reactive protocols • discover routes only when they are needed • provide small routing overhead, but higher latency • table-driven vs. source-routing protocols: • Table-driven protocols • each node only knows the next hop to a destination • the routing overhead is small, but routing loops may be formed • Source-routing protocols • nodes know the complete route to a destination • routing loops are easy to avoid, but the routing overhead is larger Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 42/69 Ad-hoc Routing Address-based Ad-hoc Routing Protocols Address-based Ad-hoc Routing Classification of Routing Protocols II. • flat vs. hierarchical protocols: • Flat protocols • all nodes run identical algorithms (=> the protocols are relatively simple) • the routing overhead may increase very fast as the number of nodes increases • Hierarchical protocols • some nodes have added responsibilities (=> the algorithms are more complicated) • the performance scales better with network size • location-based vs. non-location-based protocols: • Location-based protocols • make use of the nodes' physical location (=> reduce routing overhead) • nodes need to be equipped with GPS or something equivalent • Non-location-based protocols • oblivious to the physical location of nodes (=> simpler) • routing overhead is typically greater • and many other classifications also exist Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 43/69 Ad-hoc Routing Address-based Ad-hoc Routing Protocols Address-based Ad-hoc Routing Classification of Routing Protocols II. Based on routing information update nschg-iisrr _ Proactive (table-driven or link-state) ■ DSDV •OLSR - HSR Reactive (table-driven) • DSR •AODV ■ DYVC Eva Hladká (Fl MU) Routing protocols for ad hoc wireless networks Hybrid ZRP Based on topology information Flat routing Hierarchical routing Based on the use of temporal information for routing I DSDV DSR AODV DYVC HSR Based on utilization of specific resources I Path selection using past history Path selection using prediction 1 Energy-aware routing Geographical routing DSDV DSR AODV DYM O FORP PAR GPSR 6. Ad-hoc networks, MANETs Autumn 2021 44/69 Proactive Ad-hoc Routing Proactive ad-hoc routing protocols: • rely on a periodic collection and exchange of topology information • either table-driven (distance-vector) or link-state mechanisms for topology maintenance • table-driven (distance-vector) protocols periodically exchange routing tables between neighboring nodes o link-state distribute topology information (updates) so that each node can calculate optimal paths on their own - high network overhead for state (topology) maintenance + data packets can be forwarded at any time to any destination within the network Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 45 / Ad-hoc Routing Proactive Protocols Proactive Ad-hoc Routing Destination Sequence Distance Vector (DSDV) Destination Sequence Distance Vector (DSDV): o a distance vector routing protocol inspired by RIP protocol • based on distributed Bellman Ford procedure 9 nodes periodically exchange whole routing tables between neighbors • on topology change, incremental route updates are possible • every node knows "where" everybody else is • ^> routing table maintains O(N) items « aging information is used for maintaining fresh routes and avoiding loops • simple, but does not scale (high overhead) Dest Next D ist Seq 7 7 1 12 1 7 2 25 5 7 3 25 Routing table at node 15 Eva Hladká (Fl MU) I am 3 to 5 6. Ad-hoc networks, MANETs Autumn 2021 46/69 Ad-hoc Routing Proactive Protocols Proactive Ad-hoc Routing Optimized Link State Routing (OLSR) Protocol Optimized Link State Routing (OLSR) Protocol: • link-state based routing protocol • links' state information is flooded through the network • ^> nodes keep track of the whole topology and compute the shortest paths on their own • broadcasts (topology information distribution) are optimized through Multipoint Relays (MPRS) • instead of regular flooding, which introduces high overhead • each node selects and maintains its own MPR • the rule: ''For all 2-hop neighbors there must exist a MPR through which they can contact each other." • MPRs further allow to aggregate link-state information + suitable for large and dense networks - lack of security, no support for multicast Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 47/69 Ad-hoc Routing Proactive Protocols Proactive Ad-hoc Routing Optimized Link State Routing (OLSR) Protocol - Regular Flooding O o o o ° o o u o o o o o o o o Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 48/69 Ad-hoc Routing Proactive Protocols Proactive Ad-hoc Routing Optimized Link State Routing (OLSR) Protocol - Regular Flooding O o o o o o o Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 49/69 Ad-hoc Routing Proactive Protocols Proactive Ad-hoc Routing Optimized Link State Routing (OLSR) Protocol - Regular Flooding Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 50/69 Ad-hoc Routing Proactive Protocols Proactive Ad-hoc Routing Optimized Link State Routing (OLSR) Protocol - MPR Flooding O o o o o o o o o o o o o o o o o o 0 o o o o Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 51/69 Ad-hoc Routing Proactive Protocols Proactive Ad-hoc Routing Optimized Link State Routing (OLSR) Protocol - MPR Flooding O o o o o o o o o Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 52/69 Ad-hoc Routing Proactive Protocols Proactive Ad-hoc Routing Optimized Link State Routing (OLSR) Protocol - MPR Flooding Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 53/69 Ad-hoc Routing Reactive Protocols Reactive (On-Demand) Ad-hoc Routing • routes are discovered only when needed (when data packets need to be transmitted) + saves energy and bandwidth during inactivity - additional delay is introduced for the setup of routing information + requires no (or very small) routing tables - introduces high network overhead in the flooding process when querying for routes - performance degrades with increasing mobility Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 54/69 Reactive (On-Demand) Ad-hoc Routing Dynamic Source Routing (DSR) Dynamic Source Routing (DSR) • source-based routing protocol • uses separate Route Request (RREQ) and Route Reply (RREP) packets to discover a route from the source node to the destination • sender floods RREQ through the network • nodes forward RREQs after appending their identification • destination node receives RREQ and unicasts a RREP back to the sender node • the routing information is stored in the discovery packets • there is no need to maintain globally valid routing tables and state information in each node • data packets are sent once a route has been established • behaves well for smaller, less saturated wireless networks • optimization: route caching by observing RREQs and RREPs of other nodes Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 55/69 Reactive (On-Demand) Ad-hoc Routing Dynamic Source Routing (DSR) - Route Discovery I. Ad-hoc Routing Reactive Protocols Reactive (On-Demand) Ad-hoc Routing Dynamic Source Routing (DSR) - Route Discovery II. Broadcast transmission > Represents transmission of RREQ Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 57 /69 Ad-hoc Routing Reactive Protocols Reactive (On-Demand) Ad-hoc Routin Dynamic Source Routing (DSR) - Route Discovery III. Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Ad-hoc Routing Reactive Protocols Reactive (On-Demand) Ad-hoc Routing Dynamic Source Routing (DSR) - Route Discovery IV. Reactive (On-Demand) Ad-hoc Routing Dynamic Source Routing (DSR) - Route Discovery V. Ad-hoc Routing Reactive Protocols Reactive (On-Demand) Ad-hoc Routing Dynamic Source Routing (DSR) - Route Reply Ad-hoc Routing Reactive Protocols Reactive (On-Demand) Ad-hoc Routing Ad Hoc on Demand Distance Vector (AODV) Ad Hoc on Demand Distance Vector (AODV) • another reactive routing protocol, searching paths between the source and the destination on demand • basically, the same route discovery procedure is used as in DSR • however, it copes with the per-packet overhead introduced by DSR • (source-routing - the whole route has to be stored in each packet) o in AODV, all nodes remember from where a packet came and populate their routing tables with that information • i.e., intermediate nodes in a given path maintain routing tables instead of using source routing • when an intermediate node knows a route to destination from previous communication, it may answer to RREQ instead of the destination node + lower connection setup delay (compared to DSR) Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 62/69 Ad-hoc Routing Reactive Protocols Reactive (On-Demand) Ad-hoc Routing Ad Hoc on Demand Distance Vector (AODV) - Route Setup RREQs are flooded through the entire network (limited by a TTL describing the maximum network diameter) r^v—4 RREQ [1 to 2] \ RREQ [1 to 2] RREQ [1 to 2] RREQ [1 to 2] RREQ [1 to 2] 10 RREQ [1 to 2] RREQ [1 to 2] RREQ [1 to 2] 7 Node Dest Next Dist 7 1 1 1 11 1 7 2 15 1 7 2 ... ... ... ... 2 1 15 3 Routing tables after flooding the RREQ [1 to 2] Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 63/69 Ad-hoc Routing Reactive Protocols Reactive (On-Demand) Ad-hoc Routing Ad Hoc on Demand Distance Vector (AODV) - Route Reply The RouteReply (RREP) is unicasted towards the source Node Dest Next Dist 7 1 1 1 7 2 15 2 11 1 7 2 15 1 7 2 15 2 2 1 2 1 15 3 Routing tables after sending the RREP [2 to 1] Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 64/69 Reactive (On-Demand) Ad-hoc Routing Dynamic MANET On Demand (DYMO) Dynamic MANET On Demand (DYMO) • successor of AODV • reduces the overhead in route setup and route maintenance From: A Fro~ A From: A AODV (a^ __---^ ------ ^---^ From: D From: D From: D Path: A Path; A-B Path: A-B-C DYMO Path: D-C-B Path; D-C Path: D Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 65 / 69 Ad-hoc Routing Specialized Routing Protocols Specialized Routing Protocols Geographic Routing • instead of maintaining routing tables (to know nodes' positions), infer this information from physical placement of nodes • nodes know their geo coordinates (GPS, location service mapping node ID to node position, etc.) • send a message to a neighbor in the right direction as next hop • e.g., DREAM, GPSR, LAR Energy-Aware Routing Protocols • take the nodes' energy capacity into account • several metrics can be employed: • minimize the energy consumption per packet (selecting paths with minimum transmission energy) • minimize the variance in node power levels (preffering nodes with higher energy level) • etc. Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 66/69 Conclusion & Information Sources Lecture Overview Wireless Ad-hoc Networks • Motivation • (Mobile) Wireless Ad-hoc Networks • Wireless Sensor Networks • MANETs vs. WSNs • MANETs vs. P2P Q Medium Access Control in Ad-hoc and Sensor Networks • Protocols' Classification • Contention-based protocols • Improving Energy Efficiency Q Ad-hoc Routing • Address-based Ad-hoc Routing Protocols • Proactive Protocols • Reactive Protocols • Specialized Routing Protocols Q Conclusion & Information Sources Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 67/69 Conclusion & Information Sources Conclusions • (mobile) ad-hoc networks appear to be a good solution not only for temporary networks • but for fixed installations as well (buildings, cities, etc.) • provide many useful features as compared to infrastructure-based wireless networks • alive and well-researched area • still many challenges & research objectives: • network lifetime • robustness & fault-tolerance • in-network processing 9 quality of service • software management (i.e., nodes' reprogramming) • etc. Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 68/69 Information Sources Fl Courses: 9 PA151: Advanced Computer Networks (doc. Staudek) • PV169: Communication Systems Basics (doc. Staudek) Literature: • Falko Dressier: Self-Organization in Sensor and Actor Networks. John Wiley & Sons, 2007. • Jon S. Wilson: Sensor technology handbook. Newnes, 2005. • Ana nth ram Swami: Wireless sensor networks: signal processing and communications perspectives. John Wiley & Sons, 2007. • Holger Karl, Andreas Willig: Protocols and Architectures for Wireless Sensor Networks. Wiley-lnterscience, 2007. • Amiya Nayak, Ivan Stojmenovič: Wireless Sensor and Actuator Networks: Algorithms and Protocols for Scalable Coordination and Data Communication. Wiley-lnterscience, 2009. • ... Eva Hladká (Fl MU) 6. Ad-hoc networks, MANETs Autumn 2021 69/69