F4280 Technologie depozice tenkých vrstev a povrchových úprav 3. Evaporation Lenka Zajíčková Přírodovědecká fakulta & CEITEC, Masarykova univerzita, Brno lenkaz@physics.muni.cz jarní semestr 2017 Central European Institute of Technology ^ U*U i BRNO | CZECH REPUBLIC ^*$L*^ • 3.1 Introduction to Evaporation • 3.2 Thermodynamics of Evaporation • 3.3 Evaporation Rate • 3.3 Alloys • 3.4 Compounds • 3.5 Sources for Thermal Evaporation • 3.6 Sources using Energetic Beams • 3.7 Transport • 3.8 Monitoring of Deposition Process F4280 Technologie depozice a povrchovych uprav: 3.1 Introduction to Evaporation Lenka Zajíčková 3/21 3.1 Introduction to Evaporation Vysokoteplotní, nebo vakuové naparování (čistě fyzikální proces) se skládá z několika po sobě jdoucích kroků: 1. Získání par vypařováním nebo sublimací kapalných nebo pevných materiálů =^ nutno zahřívat na dostatečně vysokou teplotu. 2. Transport par od zdroje k substrátu. 3. Kondenzace par v podobě tenké vrstvy na chlazeném substrátu. Vytváření tenké vrstvy uhlíku naparováním bylo pravděpodobně poprvé pozorováno Edisonem. První nanášení tenkých vrstev roztavením drátu velkým proudem je historicky přisuzováno Faradayovi. První využití vakua pak Nahrwoldovi, Pohlovi a Pringsheimovi. F4280 Technologie depozice a povrchových úprav: 3.2 Thermodynamics of Evaporation ka Zajíčková 4/21 3.2 Thermodynamics of Evaporatioi Consider either a single element or a pure compound that does not dissociate upon evaporation. Vapor-liquid or vapor-solid The system is closed (no mass crossing) but equilibrium situation in a closed ^ energy in a form of heat q can be added causing isothermal container: the pressure evaporation is pv, molar condensation rate Qc and molar evaporation rate Qv are * ener9y in tne form of mechanical work balanced w = PvA^ is removed from the resulting vapor as it pushes back the surrounding atmosphere (the piston) Not all of the heat input can be transformed into work, most is consumed in increasing the internal energy U ► kinetic internal energy (discussed in chapter 2 in relation with heat capacity) ► molecular potential energy Ep - accompanies removal of molecules from condensed phase into vapor phase ail + dw = dg (1) Consider a process involving slow changes in temperature and pressure (7~ and p), i.e. carried out close to equilibrium. The system can be brought back to its original state -reversible process obeying Increase of entropy S is a measure of the degree of randomization of energy that was initially in a form out of work could be extracted, such as a difference in p, T or concentration. If the work of the force exerted by the piston was not used to store mechanical energy but it was dissipated as heat (by friction) total S would increase. S = kB In Z (3) where Z is number of quantum states. Reason for In Z - energy terms (S) are additive whereas probability terms are multiplicative Example of entropy increase involving a concentration difference: =^ increase of entropy from 0 to 1.79/cB (2) ► At fixed energy, entropy tends towards a maximum as the system approaches equilibrium. ► At fixed entropy, energy tends towards a minimum as the system approaches equilibrium. In evaporation, and many other processes, both energy and entropy are varying: Removal of the molecule from the potential well into the vapor phase increases its potential and kinetic energy. It increases also entropy because the molecule in vapor phase has more quantum states available to it, both in position ("configuational" entropy) and in energy levels ("thermal" entropy). Here, H is enthalpy that appeared earlier in connection to heat capacity at constant p. d(J + pdV+ TdS = dG = 0 (4) where Gibbs free energy G is introduced as G=(U + pV)-TS= H- TS. (5) F4280 Technologie depozice a povrchovych uprav: 3.2 Thermodynamics of Evaporation Lenka Zajíčková 7/21 Thermodynamic Quantities ► The enthalpy H is the energy term used for processes at constant p, where pdV work is being done on the surroundings. ► The internal energy U would be used for processes at constant V. Diiferentiating Eq. (5), we have dG = dU + pdV + dpV - TdS-dTS (6) that reduces to Eq. (4) at constant T and p, such as evaporation and many other processes in thin-film work. =^ System held at constant p and T is at equilibrium when dG = 0 (G is at minimum) for any disturbance such as evaporation of d/Vm moles of condensate. During evaporation, H t but it is compensated by S t- G = (U + pV) - TS= H- TS At higher T the entropy term TS becomes more important (increasing thermal motion produces randomization) =^ more H can be compensated =^ pv increases with T Evaporation can proceed by absorption of heat from surroundings (evaporative cooling), which creats a T difference. Then, it is driven by S t accompanying the evaporation =^ example of endothermic (heat absorbing) reaction. Incremental change in G for addition of material to a phase at constant T and p (applied to multicomponent mixtures) where /i,- is chemical potential of component /, A/m/ is the number of moles of component /. For a single-component system, such as evaporating pure condensate, n is just the free energy per mole of condensate, Gmc- At vapor-liquid equilibrium of closed vapor + liquid system, G of the total system does not change as evaporation proceeds at constant T and p Mc = Mv (8) where c and v denote the condensed and vapor phases. In practice, the system must be slightly removed from equilibrium so that the heat of evaporation can flow into it along a T gradient. (7) F4280 Technologie depozice a povrchových úprav: 3.2 Thermodynamics of Evaporation Lenka Zajíčková 9/21 P (atm) / ^—Equilibrium ^—Equilibrium \ CRITICAL POINT solid liquid 7 ^ freezing vaporization deposition TRIPLE POINT T fC) ► At any point along vapor-liquid (or solid) equilibrium curve /xc = Mv holds. ► As we move up the curve, /x values of both phases increases d/ic = d/Xv or for pure material dGmc = d G mv Using Eq. (6) and equilibrium conditions Eq. (4) dG Vdp - SdT or dGmi Vmidp - Smid7 where / = c, v. Thus, at equilibrium between the two phases Vmc dpv — Sme d T — V'mv dpv Smv d 7" dPv d7" mc AS m mc A K (9) (10) m F4280 Technologie depozice a povrchových úprav: 3.2 Thermodynamics of Evaporation ka Zajíčková 10/21 Clausius-Clapeyron Equation and pv on Since AGm = 0 for evaporation, we have from G = H — TS that AVH = 7~ASm where AVH is the "latent heat" (enthalpy change) of vaporization per mole. The heat of vaporization is an H term rather than a U term because it is measured at constant p, not constant V and, thus, it includes the pAV work of expansion. Substituing AvH/7for ASm = Smv - Smc in Eq. (10) leads to Clausius-Clapeyron eq. The volume term AVin = Vmv - Vmc may be eliminated: ► VmC is negligible - it is typically 1 /1000\/mv at 1 atmosphere ► for ideal gases \/mv = RT/p pv = Bexp(-AVH/RT) (13) This exponential expression is familiar from all thermally activated chemical processes, evaporation being an example. It is very useful for estimation of pv if Pv(7~) data are not available. M TJ 2 T1' S." í O.J í » T-IM " JU l.í 1.5 _■ I ľ.a dpv d7" dpv Pv A v H 7AK m AyH (11) d7" (12) Uapoi Pie-Kur» CufM» dI Liquid and Selld Smimi l.t 1.» i Í.í U i.É í.í j S.í Í Í Jí IJt i *.Í AA l.t U í U lMfrTtrr^KHtw [K] F4280 Technologie depozice a povrchových úprav: 3.3 Evaporation Rate 3.3 Evaporation Rate - Effusion Rate Lenka Zajíčková 11/21 Closed system from previous discussion is modified by opening an orifice, which is small enough =^ Qe does not significantly reduce the pressure, i.e. p « pv. ► For orifice with small diameter L, Kn = X/L > 1, i.e. molecular-flow regime. ► If the orifice length > orifice diameter the effusion rate Qe can be easily derived. The mass flow or throughput Q is usually expressed in Pa.l/s 0= Cop (14) where C is conductance, 5p is the pressure difference across the element. For molecular flow, the flux through the orifice in each direction is the flux at the plane of orifice (A is the area of orifice) P_ ~" Q = (r2-r1)/\ = (p2-p1) r, = V27t/cb 7/77 A V27t/cb Tm (p2 -Pi)C (15) Close to vapor-liquid (or solid) equilibrium, the effusion rate Qe from the Knudsen cell (vapor source with small orifice, outside pressure negligible p<\ « 0) can be found just from the vapor pressure pv: Qe = p^ A V27t/cb Tm (16) F4280 Technologie depozice a povrchových úprav: 3.3 Evaporation Rate Lenka Zajíčková 12/21 Evaporation Rate Qv (for Knudsen cell and metals with atomic vapors) Since we do not want to reduce the pressure inside the cell, Qe < Qv (17) where Qv is evaporation rate from the surface of the condensed phase. How to determine Qv? We can reliably determine an upper limit of Qv. In steady state Qv = Qc + Qe (18) and Qe can be neglected Qv ~ Qc- For determination of Qv = l~v/A we use the same balance of impinging flux l~v ~ l~c. Upon impingement, there is a range of interations with condensate surface (analyzed in chapter 4 - adsorption, deposition): ► everything is reflected - lower limit, ► everything impinging condenses - upper limit l~c = l~, _£vo_r/__ p (19) Uv- A ~ A ~ V27T/cb 7777 1 y) It has been verified experimentally that evaporation occurs at the upper limit (0 for upper limit) for those metals that have atomic vapors (most metals). F4280 Technologie depozice a povrchových úprav: 1 3.3 Evaporation Rate Lenka Zajíčková 13/21 Evaporation and Cone Jensation Coefficient Previous result on Qv estimation was valid for Knudsen cell and metals with atomic vapors. We expect that rv0 is unchanged if we remove the vapor phase and consider evaporation from an open crucible (justification: evaporation of individual molecule of condensate is not retarded by the impingement of vapor molecules). For other materials l~v < rv0 and emipirically rv = avrvo (20) where av is evaporation coefficient. There is a corresponding condensation coefficient ac rc = acri (21) At equilibrium l~c = l~v =^ ac = av. Otherwise they are different functions of p, T. The coefficient av has been determined only for few materials, e.g. 10-4 for As. Generally, it is not known. —■ Unless evaporation is being carried out from the Knudsen cell, effusion rate cannot be predicted accurately and must instead be measured directly in thin-film deposition process. F4280 Technologie depozice a povrchovych uprav: 3.3 Alloys Lenka Zajíčková 14/21 3.3 Alloys - Partial Pressures Multicomponent materials bring additional complication - the composition of the vapor phase generally differs from that of the condenced phase. Different approach for ► alloys - a solid solution or a mixture of solid phases, its composition is variable over a wide range. Examples: solder alloy Pb^Sn^*, ► compounds - specific ratio of elements (stoichiometry), e.g. GaAs, Si02. ► alloy of compounds, e.g. (AIAs)x(GaAs)1_x Evaporation of compounds is discussed in next section. Consider a generalized binary metal alloy BxCi_x (well mixed liquid phase) whose component elements B and C are completely miscible at the evaporation T, i.e. atomic fraction x can vary from 0 to 1 without precipitating a second solid phase. Total equilibrium vapor pressure over the melt Pv = Pb + Pc Pb = aBxPvB Pc = acxpvc (22) where pvB, pvc are pv of pure elements and aB,c are the activity coefficients. For simplicity, "Raoult's law" behaviour is assumed, i.e. aB,c = 1, even though they generally deviate somewhat from unity due to differences between B-C versus B-B and C-C bond strengths. F4280 Technologie depozice a povrchovych uprav: 3.3 Alloys Lenka Zajíčková 15/21 Flux Ratio If the evaporation coefficients are unity (common for metals) the ratio of evaporation fluxes is =^pvb m (23) rvC 1 - x pvC V ^?b The vapor flux will be richer that the melt in the more volatile element for any composition x. F4280 Technologie depozice a povrchovych üprav: 3.4 Compounds 3.4 Compounds Lenka Zajíčková 16/21 Compounds behave very differently from alloys during evaporation: ► some compounds evaporate as molecules (ionically bonded compounds, e.g. MgF2 for antireflective coating) - similar as single-component material ► dissociative evaporation - oxides vary in behaviour, Si02 evaporates as SiO in the presence of reducing agent Si, C, H2 F4280 Technologie depozice a povrchovych uprav: 3.5 Sources for Thermal Evaporation Lenka Zajíčková 17/21 3.5 Sources for thermal evaporation Existuje několik typů zdrojů pro naparování, které využívají ohřevu průchodem elektrického proudu: ► Přímé odporové zahřívání - Tato metoda je založena na ohřívání materiálu držáku z odporového, těžko tavitelného materiálu, jako je W, Mo, Ta, Nb. Někdy se používá i keramické úpravy povrchu těchto držáků. Tyto zdroje můžeme dále dělit podle tvaru držáku, a tedy způsobu uchycení taveného materiálu. ► Drátěný držák má formu spirály. Odpařovaný materiál ve tvaru svorky U je na spirále zavěšen. Odpařovaný materiál musí smáčet spirálu, aby se na něj po roztavení nalepil. ► Drátěný držák má tvar košíku. Naparovaný materiál nesmí košík smáčet, aby po roztavení vytvořil kapku, která nevyteče. ► Držák má tvar plechové lodičky, v níž je odpařovaný materiál vložen. Lodička je přibližně 0,3 cm hluboká, 10 cm dlouhá a 1 až 2 cm široká. Výkon potřebný pro tyto zdroje je podstatně větší, než v případě drátového uchycení, ale lze deponovat tlustší vrstvy. ► Zdroj je realizován jako uzavřená pec s jedním nebo více malými otvory, kterými proudí naparovaný materiál. ► Nepřímé odporové zahřívání - Kelímek z křemene, grafitu nebo keramiky (např. korundu) je obtočen drátěnou odporovou spirálou. Pokud má materiál dostatečně vysokou tenzi par před tavením, začne sublimovat a následné kondenzát vytváří tenkou vrstvu. Nevýhodou je nízká depoziční rychlost. For more details see scanned copy of Smith's book. F4280 Technologie depozice a povrchových úprav: 3.6 Sources using Energetic Beams ka Zajíčková 18/21 ources using Energetic Beams ► Jiskrové naparování Rychlé naparování slitin, či několikasložkových sloučenin, které se normálně mají tendenci rozpadat na složky, lze dosáhnout kapáním malinkých kapek na horký povrch. Dojde tak k separátnímu odpařování na mnoha místech kdy se ale v každém místě odpaří všechny složky. ► Obloukové naparování. Zapálením elektrického oblouku mezi dvěma vodivými elektrodami dochází v místě dopadu oblouku k velkému ohřevu materiálu. Teplota je dostatečná i k odpařování Nb a Ta. Tato metoda je také často používá k naparování uhlíku na vzorky pro elektronový mikroskop. ► Technika explodujícího drátu. Tato technika je založení na explozi drátku způsobené prudkým ohřevem díky průchodu velkého proudu, řádově 106 A/cm2. Takovéhoto efektu je dosaženo polem kondenzátoru 10 to 100 /iF) nabitým na napětí ~ 1 to 10 k V. ► Laserové naparování. Obrovská intenzita laserového svazku může být použita k ohřevu a odpařování materiálu. Laserový zdroj může být mimo vakuový systém a svazek bývá zaostřen na povrch naparovaného materiálu. ► RF ohřev. Pro ohřev materiálu lze použít elektromagnetickou indukci. Ohřev lze aplikovat buď přímo na naparovaný materiál, nebo nepřímo na kelímek v němž je naparovaný materiál uložen. F4280 Technologie depozice a povrchových úprav: 3.6 Sources using Energetic Beams ka Zajíčková 19/21 ources using Energetic Beams ► Naparování elektronovým svazkem Naparování použitím odporového zahřívání má velkou nevýhodu v tom, že naparovaný materiál bývá kontaminován materiálem držáku. Také je naparování limotováno vstupním výkonem (došlo by k tavení držáku), což značně ztěžuje naparování materiálů s vysokou teplotou tání. =^ lze to obejít pomocí elektronového bombardu materiálu. Nejjednodušší uspořádání sestává z wolframového vlákna, které je žhaveno a emituje elektrony. Ty jsou následně urychlovány díky přivedení kladného napětí na naparovaný materiál. Elektrony v něm ztrácejí svou energii, čímž materiál ohřívají a dochází k jeho vypařování. For more details see scanned copy of Smith's book. F4280 Technologie depozice a povrchových úprav: 3.7 Transport ka Zajíčková 20/21 ranspor see scanned copy of Smith's book F4280 Technologie depozice a povrchových úprav: 3.8 Monitoring of Deposition Process ka Zajíčková 21/21 onitoring of Deposition Process vapor flux monitoring (ion-gauge flux monitor, mass spectrometer, electron-impact emission spectrometer) ► mass deposition - quartz crystal microbalance (QCM) ► thickness by optical methods - reflectance, ellipsometry For more details see scanned copy of Smith's book.