High-power-density sputtering of industrial-scale targets: Case
study of (Al,Cr)N

J 2024

High-power-density sputtering of industrial-scale targets: Case study of (Al,Cr)N

KLIMASHIN, F. F., J. KLUSOŇ, Martin UČÍK, R. ŽEMLIČKA, M. JÍLEK et. al.

Základní údaje

Originální název

High-power-density sputtering of industrial-scale targets: Case study of (Al,Cr)N

Autoři

KLIMASHIN, F. F. (garant), J. KLUSOŇ, Martin UČÍK (203 Česká republika, domácí), R. ŽEMLIČKA, M. JÍLEK, A. LÜMKEMANN, J. MICHLER a T. E. J. EDWARDS

Vydání

Materials and Design, Elsevier, 2024, 0264-1275

Další údaje

Jazyk

angličtina

Typ výsledku

Článek v odborném periodiku

Obor

10300 1.3 Physical sciences

Stát vydavatele

Velká Británie a Severní Irsko

Utajení

není předmětem státního či obchodního tajemství

Odkazy

URL

Impakt faktor

Impact factor: 8.400 v roce 2022

Organizační jednotka

Přírodovědecká fakulta

DOI

http://dx.doi.org/10.1016/j.matdes.2023.112553

UT WoS

001137797200001

Klíčová slova anglicky

Movable magnetron; High-power-density sputtering; AlCrN; Microstructure; Fracture toughness; Cutting performance

Štítky

rivok

Příznaky

Mezinárodní význam, Recenzováno

Změněno: 29. 1. 2024 08:21, Mgr. Marie Šípková, DiS.

Anotace

V originále

Large-scale sputter-deposition of hard protective coatings has not been prevalent as the large dimensions of the industrial targets posed an enormous technological challenge: only relatively low power (and plasma) densities could be achieved, resulting ultimately in poor performance of such coatings. Here, we introduce a novel sputtering technology allowing to reach high power densities for industrial tubular targets. This is realised on the principle of a longitudinal movement of a reduced-size magnetron inside the target. In doing so, peak power densities of 840 W/cm2 have been achieved for the overall power of 25 kW and the target dimensions of Ø110 × 510 mm. To demonstrate the effectiveness of the solution, we produced a series of cubic (Al,Cr)N coatings by sputtering an Al60Cr40 target. Most of the coatings have a stoichiometric composition, smooth surface and a moderate amount of growth defects. Significant improvements through recipe optimisation could be achieved resulting in mechanical properties (hardness, fracture toughness, wear resistance) being equal to and even exceeding those of the benchmark coatings produced by means of conventional sputtering and cathodic arc evaporation. Our results open up great potential of this novel sputtering technique for the coating industry.

Citovat

KLIMASHIN, F. F., J. KLUSOŇ, Martin UČÍK, R. ŽEMLIČKA, M. JÍLEK, A. LÜMKEMANN, J. MICHLER a T. E. J. EDWARDS. High-power-density sputtering of industrial-scale targets: Case study of (Al,Cr)N. Materials and Design. Elsevier, 2024, roč. 237, January, s. 1-12. ISSN 0264-1275. Dostupné z: https://dx.doi.org/10.1016/j.matdes.2023.112553.

@article{2366997,
   author = {Klimashin, F. F. and Klusoň, J. and Učík, Martin and Žemlička, R. and Jílek, M. and Lümkemann, A. and Michler, J. and Edwards, T. E. J.},
   article_number = {January},
   doi = {http://dx.doi.org/10.1016/j.matdes.2023.112553},
   keywords = {Movable magnetron; High-power-density sputtering; AlCrN; Microstructure; Fracture toughness; Cutting performance},
   language = {eng},
   issn = {0264-1275},
   journal = {Materials and Design},
   title = {High-power-density sputtering of industrial-scale targets: Case study of (Al,Cr)N},
   url = {https://www.sciencedirect.com/science/article/pii/S0264127523009693},
   volume = {237},
   year = {2024}
}

TY  - JOUR
ID  - 2366997
AU  - Klimashin, F. F. - Klusoň, J. - Učík, Martin - Žemlička, R. - Jílek, M. - Lümkemann, A. - Michler, J. - Edwards, T. E. J.
PY  - 2024
TI  - High-power-density sputtering of industrial-scale targets: Case study of (Al,Cr)N
JF  - Materials and Design
VL  - 237
IS  - January
SP  - 1-12
EP  - 1-12
PB  - Elsevier
SN  - 02641275
KW  - Movable magnetron
KW  - High-power-density sputtering
KW  - AlCrN
KW  - Microstructure
KW  - Fracture toughness
KW  - Cutting performance
UR  - https://www.sciencedirect.com/science/article/pii/S0264127523009693
N2  - Large-scale sputter-deposition of hard protective coatings has not been prevalent as the large dimensions of the industrial targets posed an enormous technological challenge: only relatively low power (and plasma) densities could be achieved, resulting ultimately in poor performance of such coatings. Here, we introduce a novel sputtering technology allowing to reach high power densities for industrial tubular targets. This is realised on the principle of a longitudinal movement of a reduced-size magnetron inside the target. In doing so, peak power densities of 840 W/cm2 have been achieved for the overall power of 25 kW and the target dimensions of Ø110 × 510 mm. To demonstrate the effectiveness of the solution, we produced a series of cubic (Al,Cr)N coatings by sputtering an Al60Cr40 target. Most of the coatings have a stoichiometric composition, smooth surface and a moderate amount of growth defects. Significant improvements through recipe optimisation could be achieved resulting in mechanical properties (hardness, fracture toughness, wear resistance) being equal to and even exceeding those of the benchmark coatings produced by means of conventional sputtering and cathodic arc evaporation. Our results open up great potential of this novel sputtering technique for the coating industry.
ER  -

KLIMASHIN, F. F., J. KLUSOŇ, Martin UČÍK, R. ŽEMLIČKA, M. JÍLEK, A. LÜMKEMANN, J. MICHLER a T. E. J. EDWARDS. High-power-density sputtering of industrial-scale targets: Case study of (Al,Cr)N. \textit{Materials and Design}. Elsevier, 2024, roč.~237, January, s.~1-12. ISSN~0264-1275. Dostupné z: https://dx.doi.org/10.1016/j.matdes.2023.112553.

Podrobný výpis o publikaci