| ŽEMLIČKA, Radek, Pavel SOUČEK, Petr VOGL, Mojmír JÍLEK, Vilma BURŠÍKOVÁ, Petr VAŠINA a Yutao PEI. On the significance of running-in of hard nc-TiC/a-C:H coating for short-term repeating machining. Surface & coatings technology. Lausanne: Elsevier Science, roč. 315, April, s. 17-23. ISSN 0257-8972. doi:10.1016/j.surfcoat.2017.02.020. 2017. |
Další formáty:
BibTeX
LaTeX
RIS
@article{1372240,
author = {Žemlička, Radek and Souček, Pavel and Vogl, Petr and Jílek, Mojmír and Buršíková, Vilma and Vašina, Petr and Pei, Yutao},
article_location = {Lausanne},
article_number = {April},
doi = {http://dx.doi.org/10.1016/j.surfcoat.2017.02.020},
keywords = {Tic; tribology; run-in period; machining},
language = {eng},
issn = {0257-8972},
journal = {Surface & coatings technology},
title = {On the significance of running-in of hard nc-TiC/a-C:H coating for short-term repeating machining},
volume = {315},
year = {2017}
}
TY - JOUR
ID - 1372240
AU - Žemlička, Radek - Souček, Pavel - Vogl, Petr - Jílek, Mojmír - Buršíková, Vilma - Vašina, Petr - Pei, Yutao
PY - 2017
TI - On the significance of running-in of hard nc-TiC/a-C:H coating for short-term repeating machining
JF - Surface & coatings technology
VL - 315
IS - April
SP - 17-23
EP - 17-23
PB - Elsevier Science
SN - 02578972
KW - Tic
KW - tribology
KW - run-in period
KW - machining
N2 - The importance of the often omitted running-in phase of tribological testing was studied on hard nc-TiC/a-C:H coating system selected as a representative of protective tribological coatings. The tribological measurements were periodically interrupted and the counterpart ball was replaced by a new one after every interrupted test to simulate machining applications, where the coatings are repeatedly in contact with a new material.The changes in the coefficient of friction and thewearrate of the counterpartball were foundtobedependent mainly on the roughness of the coating at any stage. It was found out that after substantial smoothening of the wear track of the measured coating, the coeffi cient of friction stabilized at the steady-state value attained in an uninterrupted long tribotest. This steady state value was reached at the very beginning of the test and initial instabilities in the coefficient of friction were no longer observed. It was also concluded that only after the nc-TiC/a-C:H coating gets smoothened enough within the wear track, the steady-state coefficient of friction can describe even applications where the counterpart is being periodically replaced by a new one.
ER -
ŽEMLIČKA, Radek, Pavel SOUČEK, Petr VOGL, Mojmír JÍLEK, Vilma BURŠÍKOVÁ, Petr VAŠINA a Yutao PEI. On the significance of running-in of hard nc-TiC/a-C:H coating for short-term repeating machining. \textit{Surface \&{} coatings technology}. Lausanne: Elsevier Science, roč.~315, April, s.~17-23. ISSN~0257-8972. doi:10.1016/j.surfcoat.2017.02.020. 2017.
|
